Pipe Joining and Fabrication

Forum
Mechanical Trades
Pipe Joining and Fabrication

If this is your first visit, be sure to check out the FAQ by clicking the link above. You will be required to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Topics	Statistics	Last Post
Ridgid 270 Any history? by gear junkie Started by gear junkie, 08-14-2014, 12:37 AM	12 responses 1,154 views 1 like	Last Post by rod man 08-04-2019, 01:36 PM
SHURJOINT GROOVED COUPLINGS - Do you know them? by micheldc55 Started by micheldc55, 07-12-2019, 08:43 AM	4 responses 292 views 0 likes	Last Post by Bob D. 07-22-2019, 06:38 PM
Ridgid 700 by Jack'D Started by Jack'D, 06-06-2019, 08:59 PM	1 response 57 views 0 likes	Last Post by PlumberTulsa 06-08-2019, 08:41 AM
Sharkbite - what is ht ebiggest size available by Cleanmen2 Started by Cleanmen2, 05-08-2019, 07:45 AM	2 responses 100 views 0 likes	Last Post by Cleanmen2 06-05-2019, 04:58 AM
Ridgid ProPress mounting pin stuck by btothekay Started by btothekay, 05-23-2019, 09:21 PM	0 responses 60 views 0 likes	Last Post by btothekay 05-23-2019, 09:21 PM
Reed Power Drives by PlumberTulsa Started by PlumberTulsa, 05-20-2019, 05:30 AM	0 responses 51 views 0 likes	Last Post by PlumberTulsa 05-20-2019, 05:30 AM
early stage 535 advice by thredz1980 Started by thredz1980, 05-14-2019, 05:04 AM	1 response 90 views 0 likes	Last Post by Mightyservant 05-14-2019, 09:26 PM
Which cutting wheel for vintage Ridgid Model No. 00 tubing cutter? by 1steven Started by 1steven, 04-27-2019, 08:32 PM	2 responses 79 views 0 likes	Last Post by rod man 04-28-2019, 08:45 PM
dope. what kind do you use, and why? by Vince the Plumber Started by Vince the Plumber, 09-27-2008, 10:25 PM	72 responses 19,501 views 0 likes	Last Post by LibertyTank 04-05-2019, 08:09 PM
50 threads on 304 stainless, little pipe experience, what should I buy? by Emesine Started by Emesine, 04-02-2019, 10:33 AM	6 responses 77 views 0 likes	Last Post by Emesine 04-03-2019, 02:52 PM
New dies seem to be tearing the threads off by jplakstis Started by jplakstis, 04-02-2019, 05:01 PM	2 responses 88 views 0 likes	Last Post by PLUMBER RICK 04-02-2019, 09:50 PM
316 SS pipe by Lutzpei Started by Lutzpei, 03-08-2019, 08:00 AM	4 responses 75 views 0 likes	Last Post by Bob D. 03-27-2019, 03:46 AM
Chain Vise or Yoke Vise? by Fesko Started by Fesko, 02-15-2019, 03:46 PM	3 responses 101 views 0 likes	Last Post by Bob D. 02-19-2019, 04:40 AM
535 manual chuck threader vibration by Donnie Estus Started by Donnie Estus, 02-06-2019, 04:32 PM	2 responses 90 views 0 likes	Last Post by Max Power 02-08-2019, 03:10 PM
Ridgid Threading machine - refurb advice request by EdZeppeli Started by EdZeppeli, 01-18-2019, 06:08 PM	7 responses 228 views 0 likes	Last Post by Mightyservant 01-19-2019, 10:33 PM
Laser level by Ridgidtool240 Started by Ridgidtool240, 12-19-2018, 09:22 PM	5 responses 134 views 0 likes	Last Post by Mightyservant 12-25-2018, 09:29 PM
Closed: horizontal band saw making poor cuts by Donnie Estus Started by Donnie Estus, 12-19-2018, 11:26 AM	1 response 41 views 0 likes	Last Post by Bob D. 12-19-2018, 02:32 PM
Ridgid 1822-1 pipe thread with auto-jaws not clamping 3/4 and smaller pipe by rgadek Started by rgadek, 11-20-2018, 04:46 PM	1 response 176 views 0 likes	Last Post by Mightyservant 11-20-2018, 08:41 PM
Shaft play by Shea Started by Shea, 11-15-2018, 05:39 PM	0 responses 61 views 0 likes	Last Post by Shea 11-15-2018, 05:39 PM
Need to join two iron pipes at 45 and 90 degrees mechanically, ie, by bolting by Rodh Started by Rodh, 11-05-2018, 11:23 AM	3 responses 152 views 0 likes	Last Post by BHD 11-06-2018, 08:46 AM

Previous 1 2 3 4 11 38 template Next

No topics found.

Mark This Channel Read

Working...

Announcement