Announcement

Announcement Module
Collapse
No announcement yet.

after marketblade guard

Page Title Module
Move Remove Collapse
X
Conversation Detail Module
Collapse
  • Filter
  • Time
  • Show
Clear All
new posts

  • after marketblade guard

    I am looking for an aftermarket blade guard for the TS3650. I would like to have dust collection underneath the table and over the blade. I have looked at excalibur and other, similar, shop made adaptations online.

    I was wondering if anyone knows if you can buy just a new blade guard with a dust collection port on it, like the one shown below, that will fit on the TS3650.

    If anyone has decent over-the-blade setup, could you post a picture so I can see how it was done?

    http://www.leestyron.com/9/90.jpg

  • #2
    Re: after marketblade guard

    I just ordered the shark guard for my R5411.
    I haven't received it yet so I can't make a judgment on it.
    But from all the reviews I was sold on it. and my 4511 guard didn't work all that well, it fell apart the first week.

    Comment


    • #3
      Re: after marketblade guard

      I don't have one but if I'm ever in a position where I can leave my saw setup in one spot I would take a serious look at the Penn State version.
      Teach your kids about taxes..........eat 30 percent of their ice cream.

      Comment


      • #4
        Re: after marketblade guard

        I believe Lee offers a version of the SharkGuard for the 3650. I know I talked to him about it a couple years ago when he was just starting work on it.

        The Penn State overarm guard is a nice setup. I like that idea but since I have my router table set in the between the rails to the right of the saw the arm would interfere with router use. I could take it off when necessary but don't like the idea of on and off all day long. If I were to move the router somewhere else I think I would go with an overarm guard with dust extraction.
        ---------------
        Light is faster than sound. That's why some people seem really bright until you hear them speak.
        ---------------
        “If I had my life to live over again, I'd be a plumber.” - Albert Einstein
        ---------
        "Its a table saw.... Do you know where your fingers are?"
        ---------
        sigpic http://www.helmetstohardhats.com/

        Comment


        • #5
          Re: after marketblade guard

          Here's another option for an overarm guard.

          http://www.woodmagazine.com/servlet/...f/dp-00097.pdf
          ---------------
          Light is faster than sound. That's why some people seem really bright until you hear them speak.
          ---------------
          “If I had my life to live over again, I'd be a plumber.” - Albert Einstein
          ---------
          "Its a table saw.... Do you know where your fingers are?"
          ---------
          sigpic http://www.helmetstohardhats.com/

          Comment


          • #6
            Re: after marketblade guard

            I just installed my shark guard today and I love it. I made a few test cuts and it worked well. It is light weight but sturdy and well made. Much better than the one that came with the saw. It has a dust port but I did not use it yet. I only wish I would have gotten it years ago for my old saw, but that really doesn't matter now does it?
            Well worth the cost.

            Comment


            • #7
              Re: after marketblade guard

              Originally posted by tbarn View Post
              I just installed my shark guard today and I love it. I made a few test cuts and it worked well. It is light weight but sturdy and well made. Much better than the one that came with the saw. It has a dust port but I did not use it yet. I only wish I would have gotten it years ago for my old saw, but that really doesn't matter now does it?
              Well worth the cost.
              Which saw are you using it on now? 4511?
              ---------------
              Light is faster than sound. That's why some people seem really bright until you hear them speak.
              ---------------
              “If I had my life to live over again, I'd be a plumber.” - Albert Einstein
              ---------
              "Its a table saw.... Do you know where your fingers are?"
              ---------
              sigpic http://www.helmetstohardhats.com/

              Comment

              Working...
              X