Announcement Announcement Module
Collapse
No announcement yet.
TS2424 router table to replace cast iron wing Page Title Module
Move Remove Collapse
X
Conversation Detail Module
Collapse
  • Filter
  • Time
  • Show
Clear All
new posts

  • #16
    Big Johnson;

    Thanks, just ordered that MuleCab router table
    thanks for the link. was just what I was lookin for, for my PC 7518 31/4 hp router ( small gloat there ) nice lookin buncha stuff there in your pic. Thanks again
    <a href=\"http://www.woodshopphotos.com/gallery/Ralphs-workshop\" target=\"_blank\">www.woodshopphotos.com/gallery/Ralphs-workshop</a><br /><br />I can fix anything......where\'s the duct tape ?? :-)

    Comment


    • #17
      Hey Big, it's good to see you posting again!

      Tcaniff ... the picture link does not work for me. Sure would like to see a photo of the Rockler table installed.
      Alan
      My Shop

      Comment


      • #18
        Big Johnson, what's the fence set up you have? Any insight into how you made it if you did? Thanks

        Murph
        murph

        Comment


        • #19
          murphinDC,
          The router fence you are asking about is made by Freud... I also bought it from Mulecab... Here is a link to it: http://www.mulecab.com/accessories.a...=1&Access_ID=7

          Here is a link to more pictures of the saw and close ups on the fence: http://home.neb.rr.com/iambigjohnson...id%20Tablesaw/
          Regards,<br /><br />Big Johnson<br /><br />Pictures: <a href=\"http://www.woodworkersweb.com/modules.php?set_albumName=albuv85&op=modload&name= gallery&file=index&include=view_album.php\" target=\"_blank\">http://www.woodworkersweb.com/modules.php?set_albumName=albuv85&op=modload&name= gallery&file=index&include=view_album.php</a>

          Comment


          • #20
            Johnson,
            I really like the router table setup. I was looking at the Craftsman TS router table extension, but this looks great too. Decisions, decisions. Anyone care to give an opinion?

            Do you leave the router in all the time? Any problems with sag from the weight?
            Marcus

            Comment


            • #21
              I leave the router in the table all the time... When I am using the saw I usually put one of my Ridgid Fliptop Stands under the router table end for support... It works great... This way when I store the saw away, I can still slide the shop vac under the tablesaw...
              Regards,<br /><br />Big Johnson<br /><br />Pictures: <a href=\"http://www.woodworkersweb.com/modules.php?set_albumName=albuv85&op=modload&name= gallery&file=index&include=view_album.php\" target=\"_blank\">http://www.woodworkersweb.com/modules.php?set_albumName=albuv85&op=modload&name= gallery&file=index&include=view_album.php</a>

              Comment


              • #22
                Very good. I was a little worried about warpage, but I can see from your work that you are fastidious, so I'm not worried.
                Thanks,
                Marcus

                Comment


                • #23
                  Originally posted by Big Johnson:
                  Here is my router table that is attached to my TS2424 LS with the rails slid to the right now being a 3612... The table is from Mulecab http://www.mulecab.com/products.asp?...ucts=3&x=9&y=1

                  Hey Johnson I checked out Mulecab.com and they have 3 tables 27", 22", and 20". I have a Ridgid 3650. Will you answer my dumb question of the day? What do those inches stand for and which one will fit my machine You guys sure make me jealous.
                  If a butterfly didn\'t have wings, they\'d call it a butterwalk.

                  Comment


                  • #24
                    Love it, just ordered one for my TS3650 along with the Freud routerfence.

                    Comment


                    • #25
                      slipriwenwet,
                      You want the 27" version if you are running a normal contractors saw... 27" is the depth of your table from the front to the rear on your tablesaw... I have the M2 27"...

                      Hope this helps...
                      Regards,<br /><br />Big Johnson<br /><br />Pictures: <a href=\"http://www.woodworkersweb.com/modules.php?set_albumName=albuv85&op=modload&name= gallery&file=index&include=view_album.php\" target=\"_blank\">http://www.woodworkersweb.com/modules.php?set_albumName=albuv85&op=modload&name= gallery&file=index&include=view_album.php</a>

                      Comment


                      • #26
                        Big Johnson,

                        Just wanted to extend my thanks for your help in getting the mulecab on my TS2412. Took a while just bc of the holiday shuffle but it works great!

                        Murph
                        murph

                        Comment


                        • #27
                          I was notified by Accusquare(Mulecab) over the weekend that the Freud SH5 fence is no longer available from them. They also told me it could be had from Amazon. I ordered one from Amazon for $99 w/free shipping, roughly the same price that they had offered it for. Both itmes should arrive in a few days.

                          Comment


                          • #28
                            Hey BIG JOHNSON you da man. Got that Mule and M3 fence. About $200 w/ shipping. Thanks for all your help. Got enough $$$ left over to buy me some wood.
                            If a butterfly didn\'t have wings, they\'d call it a butterwalk.

                            Comment


                            • #29
                              Glad I could help... [img]smile.gif[/img]
                              Regards,<br /><br />Big Johnson<br /><br />Pictures: <a href=\"http://www.woodworkersweb.com/modules.php?set_albumName=albuv85&op=modload&name= gallery&file=index&include=view_album.php\" target=\"_blank\">http://www.woodworkersweb.com/modules.php?set_albumName=albuv85&op=modload&name= gallery&file=index&include=view_album.php</a>

                              Comment


                              • #30
                                Originally posted by Big Johnson:
                                I leave the router in the table all the time... When I am using the saw I usually put one of my Ridgid Fliptop Stands under the router table end for support... It works great... This way when I store the saw away, I can still slide the shop vac under the tablesaw...
                                , I'm really liking this idea... I was thinking about a building a table, but hey, this looks like an even better idea. Less shop space to take up.

                                How much is a fliptop stand? Do you really not worry about warpage at all?

                                Also, I know the table will be 27" deep, but how wide is it? With my 3650 rails, I only have 15-3/8" overhang, the front rail I have 20" of over hang.

                                I don't worry about the front rail sagging, but that back rail looks kinda weak to be hanging a table from. The entire weight of the table will be resting on the rails because the cast iron table has no bolt holes what so ever.

                                [ 02-03-2004, 02:46 AM: Message edited by: m00n ]

                                Comment

                                Working...
                                X